@isazi soft reset solved it

And rocks can also contain some magnetite or ferrite that is not a friend of compass calibration 😁

@surfboomerang Sure, personal perference is debatable. Since there is a way to get it back, either by design or not, it is ok for me.

@jjorgemoura Hey Suunto Fan 😍👋🏼 i would the values from your watch write in Trainingpeaks with a 5 Zone model. Change a 5 zone model in Trainingpeaks and change there ALL values like in the watch. After that DO NOT CLICK CALCULATE only save and exit 👋🏼
For your Info: Suunto watch CALCULATE in the watch the zones from maximal heart rate. If you calculate your zones in Trainingpeaks like lactate Treshhold there is the answer why you got other values CTL ATL and so.
If you know your lactat Treshhold (measurement in Ergometrie on a doctor) then you can make your zone measurement with the Treshhold one. If not then only change in Trainingpeaks a 5 Zone model and change your values manually like in the watch 😃good luck

@ramrod just touch the HR screen and it will page over and start an SpO2 reading.

@efejota same here. S9BTi bought in January 2021…is still new and in perfect condition but the new one it’s tempting 🙂

@dmytro yes yes … the 9 serie might see some software upgrade, and let’s wait a 10 or 11 serie with a bigger new brighter hardware screen … Let’s be patient and for the moment appreciate this 9 baro which days after days I love more and more and more

update
After sending my watch + cable for servicing at my local service centre, I received a new cable.

I had this issue once again, charging stop and charge. Happened 2 times on my charge when I got my watch back. start charging from 20% to 100%.

1 week later after draining, I charge my watch and it did happen 1 time on my charge, from 40% to 91%.

I will continue to monitor this.

@dimitrios-kanellopoulos so its a bug! the fact I can change zone 1 on the app to as per screenshot 1.PTE or anything else

@lexterm77
I did that when I broke my elbow and had my left arm in a cast for 7 weeks… I still did not got used to it…

It’s now >2 years that I own the S9B and I recall that I’ve asked for a lock button in watch mode pretty soon. It’s amazing what has been developed, improved and implemented in that time. Really interesting, useful and demanding stuff (to develop)… but no lock button 😉

…sorry, I unintendedly hijacked this thread!

As @Dimitrios-Kanellopoulos says…
Below a certain temperature OHR can become very unreliable but in warmer weather it works perfectly. Just use a strap in the winter for best results.

Warm weather
Screenshot_20220205-120559_Suunto.jpg

Cold weather
Screenshot_20220205-120644_Suunto.jpg

@Erik-F If you encounter additional issues I would perform a hard reset/restore of the watch. If after that you have problems contact support.

@Bradleyd as for the walk: I think vO2 is a cumulative value, so if it didn’t change because no HR was recorded, it’s still shown at the end.

@freeheeler said in For s9p and s9b:

@outtatime
the reason could be various… assuming you just look at altitude in watch mode? or does this happen during an activity?

It looks like it can be off on the activity mode as well. So it’s not just baro. Gps has its own ellipsoid that it follows and is a rough estimate of altitude.

@zhang965

Thanks very much.
A hard reset did work. Today’s training went without any troubles. Hope, that will work further!

@jmoneygrip I agree. I also found that the OHR is fairly accurate during activity. It is reasonably close ( at least during trail runs) to what I record on my chest HR monitor. I am satisfied from that standpoint.

What annoys me are all the huge spikes in HR readings at rest and during the night. I do not probably meet the characteristics of the perfect target customer for the S9P; hence, I may care about wellness data from the watch ( and HR reading outside an activity or training) more than the average customer. However I still think this is an issue as these readings may affect sleeping scores and other metrics.

@freeheeler yes S9P only seems to have this issue.

@Tieutieu support for multiple sensors of the same kind for example. It’s so inconvenient having to unpair and pair sensors every time when using multiple hr sensors

@imperial001 Endurance mode on Vertical is better than the 9 Peak on performance mode. The Vertical has extra storage for recording because of chip for map storage. Shouldn’t be a problem for your races.
The memory of 9 peak hard to assess as HR takes up space and more space with higher intensity. A general guide is the watch will safely store #of hours that battery will last in the chosen mode.

Just wanna give a big thumbs up for Suunto. 👍

The latest firmware fixed the battery drain very good! Depleted the watch completely after the 2.19.42 firmware update and charged it to 100%

After 48 hrs the watch is still at 92% (no exercise)