Random reboots of the Suunto 7 during recording an activity
-
GOOD NEWS EVERYONE!!
After three factory resets my watch seemed to be behaving last night (was only tested indoors and not on a run). My new phone arrived this morning so I went through a fourth factory reset to connect that.
I have just been for a 7K run following a route and it worked PERFECTLY!!
It seems that multiple factory resets (three seems to be the magic number) manages to clear whatever glitch may be present.
-
@olymay said in Random reboots of the Suunto 7 during recording an activity:
GOOD NEWS EVERYONE!!
After three factory resets my watch seemed to be behaving last night (was only tested indoors and not on a run). My new phone arrived this morning so I went through a fourth factory reset to connect that.
I have just been for a 7K run following a route and it worked PERFECTLY!!
It seems that multiple factory resets (three seems to be the magic number) manages to clear whatever glitch may be present.
It’s magic!
-
Unfortunately I was not so lucky, yesterday fifth hard reset and I can still reproduce the app crash during the activity following a path. Going through the various screens you first notice a slight slowdown passing from the laps screen to the one with the altitude profile while all the others transitions are smooth. However, the problem occurs just after 5-6 km until the final crash of the app and loss of activity data. I state that I always run without a mobile phone and I also tried to activate the airplane mode to see if anything changes, obviously without success.
-
@sherani That sounds like a right pain in the a**! It also sounds like yours it lasting significantly longer before crashing than mine did (mine was crashing as soon as it tried to go into power saving mode).
By hard reset, do you mean a full disconnect and factory reset? If not, I would suggest trying this, and it may take a few times (it took me three!). If that is what you have done, then you may have to send it back to Suunto
-
Hello guys.
As you know I reported the bug and response is that it’s known and top priority at Suunto. Should be fixed with next update but unfortunately third-party (hardware provider) is involved so no ETA. -
BAD news everyone!
After a successful run on Thursday where my Suunto 7 worked perfectly whilst following a run, I went out today on the exact same route, with the exact same settings aaannnnddddd…
IT CRASHED!!!
However, this was different to previous issues. I started off on the default running info screen so I could keep an eye on my pace. When I got to the part of the route with a number of turns, I switched to the map view (I have this set to always on screen) so that I could easily and quickly see where I needed to go.
After maybe 10 minutes of this mode, I switched back to the default screen to check my pace. I left it on this screen and when it switched to the powersaving display (thinner fonts etc) it crashed the Suunto Wear App and went to my clock face. Cue much swearing from me!!
This was at around 5km in the run, when in the past it crashed at around the 1km mark or sooner.HOWEVER… I again opened the Suunto Wear App a little further in the run and it it openedd on the default running screen and was still tracking my run with all data present and correct!! Great I thought, it was just a blip. But, once it tried to go to the powersaving display again, it crashed again.
I tried this a few times and the same thing happened every time. I decided to stop fiddling as it seemed to be continuing to track my run, just without showing it to me.
At the finish line I was able to open the Suunto Wear App (it was still tracking!) and stop the run fine. When I got home it synced the data to my phone as normal, which is a huge relief!However, this is a £400 activity focussed watch that seems to require a factory reset before every run in order to work properly.
Am I frustrated? Nope. I am absolutely &@%$ING SEETHING FURIOUS!!
-
@olymay so sorry to read that. I’m frustrated reading you. So I don’t know what to tell you more than reach support and ask for a solution.
At least we’ve discovered is a bug know and top priority to fix it but without ETA.
Tu comunidad Suunto en Telegram: https://t.me/suuntocommunity (spanish)
-
@Bulkan I have contacted support on three occasions. Every time they log my issue and inform me that someone from the technical team will contact me within 24-48 hours. I have never been contacted. I have utterly given up with Suunto customer service.
Reading Pavel’s comment about Suunto acknowledging the issue (this part is good news) then saying they are relying on a third party, WHAT!?!? Firstly, this is a software issue, not hardware - the fault was introduced after the recent update. Second, I was under the impression that a Suunto watch would be made by Sunnto. What third party are they referring to? Or are they just fobbing off because they are either unable or unwilling to fix it?
I’m now starting to look at my friend’s Garmin Fenix 6 with more and more envy
Suunto 7 Graphite Copper
Suunto App Beta (Android - Pixel 6 Pro) -
@olymay I think they are referring to Google. The watch is a partnership.
-
@olymay the suunto 7 uses wearOS that’s google.
Look at the page of suunto of your country and give them a call.
-
@olymay Well, Suunto produces devices and writes software - but all this work is based on components from different suppliers - one company supplies a heart-rate sensor, another - chipset and so on. Typically all this components come with SDK which may also contain bugs and etc.
I quite understand your frustration (I have similar issue) and sorry for that, but well - as for all affected it started to happen without clear reason why I am not surprised it haven’t been found during testing - this shit happens even to expensive products.
I’ll keep an eye on it and let you know if there is any news. Let’s wait for next update. -
@Brad_Olwin Possibly. But the problem seems to be with the Suunto Wear App, which I doubt Google have much (if any) involvement with.
@Bulkan I have done this. Three times. Each time they promise someone from ‘Technical’ will get bet to me within 24-48 hours. This has never happened. I expect better when I have spent over £400 on one of their products.
@pavel-samokha You have a point there, maybe there is a clash between components/software. But it seems to be purely within the Suunto Wear App since the recent update. As it seems to crash (at least for me) when the display switches to the powersaving mode, maybe as a short term fix they could give us the option to dissable this powersave screen? At least until they fix the greater problem here. AT least it would allow me to use the watch as per it’s intended function.
I know I am ranting here, and I work in technology so I really do understand that this sort of thing can (and does) happen. I am mostly angry at the appalling customer service. Promising to get back to me and then they don’t. Each time I call up they tell me this is a highly unusual problem and they have never heard of it before (they clearly do not read these forums then do they!). They have suggested sending my watch back for a month (they will have it for 14 working days, plus transport and processing either side, comes to roughly a month) and it sound like that won’t remedy the situation at all.
I am getting much better info and response from here on the forums.
I am angry at the response by Suunto. I don’t want to take my frustrations to social media, but I may have to resort to that in order to get a response and acknowledgement from Suunto.
Suunto 7 Graphite Copper
Suunto App Beta (Android - Pixel 6 Pro) -
@pavel-samokha
Do you know when (approximately) will be available the next firmware update?
-
@olymay said in Random reboots of the Suunto 7 during recording an activity:
us the option to dissable this powersave screen
It makes sense to me, I’ll try to pass this to the team.
@olymay said in Random reboots of the Suunto 7 during recording an activity:
I am mostly angry at the appalling customer service.
Not an excuse, but possible explanation I see is that first-line customer service is really can’t do anything with modern bug except to offer you to get watch for service.
@Mi_chael said in Random reboots of the Suunto 7 during recording an activity:
Do you know when (approximately) will be available the next firmware update?
Sorry, even if I had known I wouldn’t comment on anything like release dates - both because it may change due to various reasons (like a major bug in last minute) and just I suppose I’m not allowed to. Trying to do my best to be helpful here and not saying anything forbidden, probably I need a masterclass from @Dimitrios-Kanellopoulos
Opinions expressed are solely my own and do not express the views or opinions of my employer
-
@pavel-samokha
Ok, don’t worry. I understand.
-
@olymay said in Random reboots of the Suunto 7 during recording an activity:
But it seems to be purely within the Suunto Wear App since the recent update. As it seems to crash (at least for me) when the display switches to the powersaving mode
Exactly the same experience here. And I think it depends on one of the settings in “gestures”, which also activate the coprocessor if a powersaving watch face is choosen.
I enabled AOD therefore and I think this is a solution to avoid this bug. Try to use it and disable all the options in “gestures” except “tap to wake”.
Maybe it’s working.
https://www.instagram.com/moves.are.life/
Suunto Vertical Black Lime
Suunto 9 Peak Pro Black
Suunto Spartan Ultra Stealth Titanium -
@pavel-samokha Thank you! You are doing a grand job and in just a few messages have given me way more information than three calls to customer service which have totalled over an hour.
I’m sure you already have done, but please stress to Suunto that this has rendered the Suunto Wear App on my watch completely useless.
I do realise that the first-line customer service are limited in what they can do, but when they promise that the Technical Team will contact me in 24-48 hours and I get nothing, either they are lying to me, or the Technical Team are ignoring me. Either way, that is poor and I am furious.
I have now just factory reset my watch for the fourth time in a week. I should not have to do this with a £400 watch (in fact I would be annoyed if I had to do it with a £40 watch!!).
Again, Pavel you have been great and seem to be making progress with Suunto that the rest of us are unable to do so.
I know you are unable to give us any dates as to when a fix may be released, but if you could give us a rough estimate (i.e hopefully within the next four weeks) please? If this goes on for much longer then I will be returning my S7 and getting something that actually works (maybe go back to my £10 plastic Casio!)
-
@pilleus Interesting! I will try a few combinations.
My usual settings are:
AOD: On
Tilt to wake: Off
Touch to wake: Off -
@olymay there is a third option in “gestures” for Suunto’s watch faces which are listet to save energy. I think this may cause the issue. With other watch faces it’s grayed out.
I used the 3100 essential watch face during the period of crashes,which is also designed to use the coprocessor.
Now I use a different watch face and didn’t experience the problem until now.
https://www.instagram.com/moves.are.life/
Suunto Vertical Black Lime
Suunto 9 Peak Pro Black
Suunto Spartan Ultra Stealth Titanium -
@pilleus Ah, yes, I know what you mean, the ‘power saver watch face’ with ‘power saver tilt’.
I use the default Heat Map watch face (it’s gorgeous!) with the power save feature turned on. I will try disabling this and see what happens…
EDIT
Just disabled the ‘power saver tilt’ and it made no differenceSuunto 7 Graphite Copper
Suunto App Beta (Android - Pixel 6 Pro)
