Anyone else's storm alarm not triggering?

[A Former User]

@Umer-Javed nope until now as I also said in the other thread (my suunto core caught all the bad weather fronts though)

[babychai]

-deleted-

[A Former User]

@gi0vanni right now a severe weather front with hail has just hit my house and the storm warning has been triggered

[Umer Javed]

@gi0vanni Thank you!

Just yesterday we were hit by a storm while climbing. Crept on us and was more than what was forecasted. I checked the pressure drop on windy and it showed a little over 4 hPa over the last four hours. I didn’t get an alarm and I keep my watch in my backpack at the base on single pitch routes, so it wouldn’t have seen any other change other than pressure. We were at the crag for 7–8 hours by then.

I’m guessing I picked the short straw and have either been lucky with fronts that move just slow enough to not get picked up, or maybe the watch thinks I’m moving and doesn’t trigger on fronts that are just at the threshold.

But thanks for confirming that it does work.

[freeheeler]

@Umer-Javed
I understand from the manual that pressure drop needs to be detected by the watch.

during an activity with altitude change, the watch changes from baro to alti:

[Frederick Rochette]

Same here, never had a storm alarm with Suunto vertical

[A Former User]

@freeheeler my suunto core detects storm warnings quite well but, unlike others, the watch has to be put in barometer mode… I would love something similar on my S9PP

[freeheeler]

@gi0vanni
I want my watch in alti mode during an activity in the mountains. on the lake baro mode is fine.
in my understanding we can not have both. storm alarm is triggered by pressure drop. during an ascent we will always have pressure drops.
we ascent much faster than 4 hPa in 3 hours (4 hPa ~30m).
maybe it’s too much of a ridge walk in the evaluation to filter pressure drop from ascent to deliver reliable alerts? I don’t know, it’s just a thought

[Mff73]

@freeheeler
i assume (just assume) that, with fusedalti, new watches are able to distinguish part of pressure change (absolute = mesured) which is due to altitude change (in activity) and the part due to weather changes.
I already had storm alarm during activity.

[Egika]

@Mff73 you are correct.
The sea level pressure is always there to be judged by the storm alarm algorithm.

So it can work during or outside an activity.

[freeheeler]

@Egika
I think I don’t understand the manual entirely

[Egika]

@freeheeler good idea. The manual has the data:
’ > 4hPa in 3h is the trigger level

[Croatoan]

Mine activated yesterday

[Umer Javed]

@Egika @freeheeler

Thanks guys. As I mentioned in the posts. My watch is in my backpack at the base of the cliff for 6-7 hours as I climb, or on my wrist at my desk for the day as the storms roll in.

As Giovanni & Croatoan confirmed, the alarm works. That’s all I needed to know.

My amateur hunch is that somehow all these 6-7 storms that have rolled in have either been just at the border of 4 hPa/3 hrs or somehow the watch is sensing it as an elevation rise even though I’m not moving vertically. I don’t think I have the tools to confirm this so hence this thread.

[Egika]

@Umer-Javed you can check historical weather station pressure data to judge your events

[Umer Javed]

@Egika yeah for certain locations I was able to see drops of 4over3 which triggered the whole discussion here but I can imagine the drop at the weather station can be slightly faster or slower than where I am. So unless I carry a second barometer I can’t say for certain. Or the watch tracks it as movement especially when I’m at the base of a cliff and GPS signals are reflecting.

Maybe I need to get my Ambit out of the closet and compare side by side for the next weather event.

Honestly, not the end of the world but nice to have it work as it used to. This is just the geek in me speaking out…

[A Former User]

@Mff73 I wondered about it, but since it never happened during the activities I thought it was not possible. glad to know it works!