Software Update 2.48.16 (2025 November Rain release)

jjpaz

@v.sacre The reason is that, after first activity with BT sensors connected, increased battery drain can happen after finishing the activiy. My “workaround” is to soft reset the V1 after every activity… This bahavior keeps the battery drain in a “stable” drain.

I can test the “zombie BT process” powering on my Coospo HR armband, V1 vibrates as if it was connected to the sensor.

And this doesn’t seem to be happening in my Race S.

Stavrogin

@runomatic I think there is something to what you just said. Coros shuts off, but others do not. I had to replace my Garmin HRM Pro + battery that had 85% before the update after the update. Left the HRM hanging in my bathroom. I think that it was connecting every time I was in range. I do not use the HRM enough to go from 85% to 5% in a couple weeks. When I approach the HRM pro + when it is dry it does not automatically connect. However any time I am in range of it while the belt is wet it will connect. Even just when I walk by and am in the connectivity settings.

Stanislav Damjanov

@Александр-Даниленко I can confirm this, swimming algorithm is broken. I don’t really know if it is because of the latest firmware, or Race 2 (I have switched from Race), but last time I had swimming training watch missed distance by far. At the end of training I was paying more attention, it missed almost every second 25m distance, I counted more than 10 missed distances. My swimning style is exactly the same it was before, and usually it missed one or two distances in about 2.5km.

Tomas5

This are my notes of battery status with this firmware:

14.11. 19:20 100%
15.11. 20:19 94%
16.11. 21:14 87%
17.11. 18:27 81%
18.11. 20:12 71% (1h40m GPS)
19.11. 20:36 65%
20.11. 18:32 57%
23.11. 19:08 37% (20m non-gps)
24.11. 22:00 27% (20m non-gps
25.11. 17:53 20%

It looks like it would do around 13,5 day if i went from 100% to 0%. I run it with AOD off, low brightness and as you see i did almos no excercise. Since with 24/7 tracking it is advertised up to 18 days of battery life. This is not ideal but it is not worst too. I would expected at least 15-16 days with excercise i did.

Update after charging to 100% i did soft reset, its mutch better:

25.11. 20:15 100%
26.11. 19:56 96%
27.11. 19:55 91%

SuperFlo75

@runomatic I use only the Suunto HR Belt which seems to make trouble I wrote about this some days ago

gone troppo

I have been recording battery drain for a good while however here is my data since this latest firmware update.

21/11 100% 5:20am
22/11 93%
23/11 81%
24/11 70%
25/11 55%
26/11 42%

This is pretty typical of what i see from my vertical 1

SuperFlo75

@gone-troppo Which watch is this? If it is a SV1, it’s too high battery consumption, I think… how much training sessions do you have a day? For my usage, with about 3-4 hours of activity a week, the battery has to be charged every 4 weeks normally, and now, since the summer update about 3 weeks… it’s not bad, but it’s less than before!
But the issue with the chest strap is more annoying, because although the OHR is fine for normal running, it doesn’t work well when running with poles or cross-country skiing.

enriqueescoms

@Stanislav-Damjanov Yes, I’ve noticed the same on my 9PP

Inge Nallsson

@Stanislav-Damjanov said in Software Update 2.48.16 (2025 November Rain release):

it misseg almost every seconon 25m distance, I counted more than 10 missed distances. My swimning style is exactly the same it was before, and usually it missed one or two distances in about 2.5km.

Yes, the missed lengths have skyrocketed also for me over the almost exactly one year since I bought the Race S. Back then (December 2024) the algorithm categorized everything as "Free"style, but missed very few lengths. Then Suunto started to tinker with style identification…

What is now a fact, is that if the algorithm can’t identify the style, the whole length is discarded (instead of having a fallback to e.g. Freestyle). For me, as a competitive swimmer in the 1970s with Breaststroke as a specialty, this has a profound implication. Back then we were tought a very tight and quick arm pull, something crudely ascii-drawn like:

 _( )_
\_   _/

I am trying to illustrate a sort of < > pattern with the upper and lower arms. Using this style the algorithm discards about 80% to 100% of all my Breaststroke lengths. The watch starts to count lengths again if I use a more modern and wider competition arms style; again crude ascii:

 _( )_
|_   _|

It also count lengths quite consistently if I use the widest style of all, the slow recreational style tought by my father:

   _( )_
/         \

Apart from having to relearn a swimming style (!), the problem with a modern wide arm pull is that it relies quite a bit on muscle strength. I am 65, so that style is very exhausting. And even as a youngster the idea of the tight arm pull was to quickly get them out of the way and use the legs as the main way of propulsion.

Anyway, these are my experiences… Since I do about 50% Freestyle and 50% Breaststroke the current situation is really disheartening. Last swimming session I left the watch at home - if it can’t count, there’s little use for it.

Александр Даниленко

@pavel.samokha
@Dimitrios-Kanellopoulos

Again same problem. 1st the watch calculated 25m as 13.5 (which is close to the truth), but then I swam 25m underwater + 25m freestyle max + 25m underwater + 25m freestyle max. The watch had to count those 2 time by 25m freestyle max as separate, but they didn’t count any and changed the time for previous 25m from 13.5s to 6 minutes 47 seconds:

Therefore the overal swimming session pace is completely wrong:

The swimming in this firmware is completely broken. I compelled to go back to the previous firmware…again

mlakis

@Dimitrios-Kanellopoulos, just tried also a pair of Favero Assioma pedals, same behaviour, menu says obtaining crank length, setting the length reports OK but then the message about obtaining the length remains, and sensor is not visible when selecting the cycling training.

Thanks in advance

Ecki D.

9PP WHR 24/7 stopped working during night again

Last night the 24/7 HR Measurement stopped working again. I just noticed it because after waking up the passcode was activated again and again.

This time turning on energy save mode and turning it off again fixed it.

Can’t remember when this happend to me last time. Thought it might have been fixe but it seems like it is still happening.

It seems like the option to send logs to support ist gone in the app, or do I just don’t find it?

Egika

@Ecki-D. seems like the watch thinks it is off your skin.

Gideon Kaempfer

@Ecki-D. Sending logs still exists under account (right top picture of a person) -> settings:

2b2bff

@Egika said in Software Update 2.48.16 (2025 November Rain release):

seems like the watch thinks it is off your skin.

I guess that is what happened with my Race S as well - as written here

Ecki D.

@2b2bff @Egika - Yes, that’s my impression as well. Once the sensors switch off, it probably triggers the whole ‘off-skin mode’ logic. Kind of a chicken-and-egg situation that only Suunto can really sort out — is it falsely detecting no skin contact, or are the sensors shutting down for some other reason?

Just to add my perspective:
It’s frustrating that a basic issue like the nightly sensor shutdown is still around. This isn’t an isolated case — several users report the same behaviour, and it has a real impact on sleep/HRV tracking.

The watch is great in many ways, but when such a core function keeps failing, it becomes hard to trust the device long term. Some users even joked at me that the only reliable “solution” is to return the watch after 11 months and hope the next model fixes it — which says a lot about how long this problem has been known.

It would be really appreciated if Suunto could take a closer look and address this properly. The hardware seems capable; it feels like a firmware issue that should be solvable.

Matúš

@Ecki-D. said in Software Update 2.48.16 (2025 November Rain release):

9PP WHR 24/7 stopped working during night again

A shiver runs down my spine…

Currently, @Jaxxdu (https://forum.suunto.com/post/180232) and you had (again) the “pleasure” of this bug… Very very well! So, I’m waiting for it.

Stanislav Damjanov

I had another swim session today, once again watch missed 8-10 25m distances in 2500m. It is quite frustrating, last year in June before firmware update which supposed to fix swim style detection it was quite accurate, it was often that even one distance wasn’t missed for thewhole session. After that update it was worse but it was acceptible to miss few distances, but now it’s a disaster.

v.sacre

I still don’ t understand how to see new running metrics (ground contact etc).
I use Vertical 2 with latest firmware, with or without Stryd, with or without custom mode and in all cases I don’t see those metrics…

OutdoorMan

@v.sacre I don’t have these on watch screen but these details are visible in the activity summary after you finish a run or in Stats in the app. Do you see this?