Software update 2.13.18 for S series (S3,S5,S9)

[Rob33]

the best autonomy remains in GPS alone?

[Brad_Olwin]

@Rob33 You can and I have, but using a belt or turning off OHR will help more than which satellite system you use. In my experience I have found the estimates on the watch tend to over estimate rather than under estimate the time. @Łukasz-Szmigiel and @markytarky I would not assume the duration that the watch is providing is completely accurate and as I mentioned before a real test in real conditions will give you a better idea. I mostly test GPS only but I have seen improvements in battery life for me using Performance and Endurance modes during testing of this firmware.

[Łukasz Szmigiel]

@Dimitrios-Kanellopoulos pretty reasonable, thanks for the info.

@Brad_Olwin, I suppose that in a rare occurrence when battery life is paramount I’d use GPS only. However I personally don’t see a situation where I might need more than 20h of constant tracking. One can charge a watch with even the smallest of power banks that don’t add much weight to equipment so why bother? Just wanted to know if a bug slipped through or the difference was too small or too variable to report it in activity start screen.

[Brad_Olwin]

@Łukasz-Szmigiel I personally hate to charge my watch, carry cables and have all of that hassle when racing ultras. The challenges of the race are far more important to me than a precise GPS track. So, I used FusedTrack and never have to worry about charging. If my event is ≤36h I will use Endurance mode and if ~48h for the cutoff, I will use Ultra mode. I typically wear the Smartsensor belt. So, weight is not the issue.

[nseslija]

@Dimitrios-Kanellopoulos Great…

[Łukasz Szmigiel]

@Brad_Olwin also pretty reasonable. Most ultra runners I know don’t even bother with hr, let alone the track quality. Some charge their watches during the race, others don’t or don’t have to, but if I were to run an ultra I guess that the last thing I’d like to worry about was the watch. I was rather referring to hiking or multi day activities where this shouldn’t be a problem.

[stromdiddily]

Awesome update if not as flashy or sexy as some previous ones

Noticed that I received a “Wait for green arrow” notification prior to running after the update. I waited for five-ish minutes w no GPS lock. Backed out of the workout. Tried again and GPS was found in probably 10 seconds.

After the workout, I received another notification advising on how best to achieve optimal GPS results.

Wondering if this is expected?

[Łukasz Szmigiel]

@stromdiddily perhaps the watch didn’t have time to extract AGPS after the update. Did you go for your workout right after the update finished?

[stromdiddily]

@Łukasz-Szmigiel Probably 10-15 minutes between update and getting into the exercise screen…

[omunoz]

@stromdiddily
I have a joke about this , always you update or reset the watch , use the Altitude settings with location coordinates and when you have the information goes to exercise and start .

[A Former User]

@stromdiddily I’ve had this happen the first run after almost every update. It doesn’t recurr though. There must be some sort of bug in the software. It won’t be a problem going forward, unless it is.

[Łukasz Szmigiel]

I just looked at a track from today’s walk on quantified-self.io and compared it to yesterday’s run and it seems there’s a lot less areas of “less dense” points than before. Basically almost the whole path is populated with high density of points on QS and there are no long fragments with points that are spread apart. Also, the browser in my new phone didn’t die while viewing gmap with points overlaid on it so it’s another plus thanks @Dimitrios-Kanellopoulos for phone benchmarking tool on QS

Apart from fun but slightly retarded activity of counting the dots on the map I wonder: shouldn’t the new firmware result in larger fit files and therefore less activities stored in watch memory?

[Brad_Olwin]

@zrumlow said in Software update 2.13.18 for S series (S3,S5,S9):

@stromdiddily I’ve had this happen the first run after almost every update. It doesn’t recurr though. There must be some sort of bug in the software. It won’t be a problem going forward, unless it is.

It is not a bug, it takes 15 min or so for the GPS update data to populate appropriately in the watch. So make sure AGPS is updated and don’t outdoor exercise immediately after the update.

[stromdiddily]

@Brad_Olwin our definitions of immediate are different apparently but point taken to wait longer next time

[isazi]

@stromdiddily I had no issues getting a fix after the update, but between the update and me going outside hours passed. If you go into the About menu you can see if the agps is still being unpacked.

[Brad_Olwin]

@stromdiddily I am not sure how long it takes but this came up before and Dimitrios stated it can take 15 min or maybe a bit more for the AGPS data to be unpacked and utilized. Someone who knows better can correct me.

[surfboomerang]

@stromdiddily Same here, after the firmware update I noticed the '“In Progress” text under AGPS in the About menu. After a while, it changed to the date of that day. When I started an activity a couple of hours later, I had instant GPS fix.

[pacos]

Hello
“ Fix increased power consumption when in endurance or ultra mode and at the altitude chart screen (navigating)” could you explain this please? Not too clear for me. Thanks!

[Brad_Olwin]

@pacos It means when you are in ultra or endurance mode, and have a route loaded, best GPS fix will activate only when you are on the route screen or altitude profile screen. So if you use those modes, you do not want to leave the watch on either of those screens, but use them only when you need them. In Performance mode it does not matter.

[pacos]

@Brad_Olwin ok, very clear, that is great! Thanks