That’s worked, thanks It was extra annoying as the 2 orphaned routes were named very close to routes I wanted to keep and I kept getting confused. Much better now

@James-Eastwood Welcome and yes, have to wait for TSB, and keen the questions coming!

@Dragan thanks you for recommendation. It looks good. I ordered the same screen protector yesterday.

@shai-cristallo did you check if the band or the watch isn’t subject to forces applied by the back of your hand (or wrist movement at all), e.g. when doing push-ups or grabbing weights/ handlebars - anything where you lower arm muscle contract etc.? It looks like you wear it very close to your wrist ankle. I cannot wear it that close during training, because it would be too near and interfere with movement. [image: 1744792098377-img_5915.jpeg]

@Matěj-Novotný I sync all my data to intervals.icu as it is better tool for analysing activites, loging gear usage, seting zones and so on. So I import activity to SA, which is then synced to intervals.icu where TSS (Load) is calculated and then I set maunal TSS back in SA.

@rizojm is this even possible to do accurately with any watch? I’ve not heard of it without needing GPS on.

@MoTrailrunner never had such battery drain on my RACE S. Don’t know how to directly help, but here are my settings (i would say around 5% battery drain per night). For sur what drains battery the most is backlight. Maybe also notifications ? Eco mode OFF main permanent backlight setting OFF sounds : buttons OFF vibration OFF Alarm BOTH backligh : LOW permanent display OFF raise to wake DISPLAY ONLY Notications OFF H24 HR tracking and sleep tracking ON (sleep period set to 23h to 7h) VFC tracking ON SPO2 tracking OFF auto DND mode ON (same than sleep 23h to 7h)

@kaab6271 as there is an Auto DND feature I asked specifically for manual activation. So, my guess is that enabling DND makes the watch more aware of a possible sleep cycle or napping. I don’t know if it doesn’t work without enabling DND. I only tried one night and it didn’t detect sleep. But as Suunto doesn’t respect focus modes on iOS it sends all the notifications over to the watch even with “sleep” focus mode. Therefore disabling DND has not proven to be useful to me…

double post

OK I found the “Problems”: To disable the Notification sounds I needed to change two settings: Control Panel -> Settings -> General -> Tones -> All off Control Panel -> Settings -> General -> Tones -> Alarm -> Vibration I just changed the second one … bit confusing. Setting Control Panel -> “Aways on display” does keep the display on, but the WatchFace nevertheless changes to a very minimalistic one … bit confusing. And also bit confusing, there is another “Aways on display” setting here: Control Panel -> Settings -> General -> Display -> “Aways on display”

I wanted to add one more example of misleading navigation guidance. In this case not only the blue arrows are rendered behind the track but also the watch fails to recognize that I moved forward and still renders the blue arrow behind of where I am. [image: 1743869731045-pxl_20250405_003650936.jpg] This was at a crossroads of trails where I tried to figure out where to go next, and the guidance provided by the watch was misleading. In reality I was supposed to continue on that dark blue with no red part of the track. Also note the poor accuracy of following the trail. As far as I can tell the map was accurate but the tracking was not. This was using dual-band GNSS. Also, what it actually has recorded looks different from what was displayed on the watch: [image: 1743870249456-screenshot-2025-04-05-at-9.22.13-am.png] Perhaps the watch should not simplify the track at a high zoom level to help with navigation. There are situations when this might be confusing.

@gshaw34 Hear rate sensor is just bogus. I will post some heart rate screenshots in https://forum.suunto.com/topic/11854/suunto-race-s-optical-heart-rate-sensor-accuracy/13

Exactly! Hey Suunto team, this is so annoying, everytime the watch updates itself, it resets all colors and watch face. Please fix this