Software release 2.30.26
-
@renton82 The watch will only show sleep and HRV if you wore it sleeping. If you switch after wake up all data will be in SA. Steps, HR, calories and resources will be recorded from synchronized watch and seamless. ATL, CTL and TSB will be the same across all devices and app.
-
@seanvk Yes
-
@renton82 yes
-
@seanvk said in Software release 2.30.26:
The widget order is fixed
Not fixed, you can sort the widgets by dragging and dropping them in SA.
-
@Jugger said in Software release 2.30.26:
@v-sacre Hold lower button to get to Control panel, you find it there.
Thx for this hint! Now I can reduce one more down widgets.
-
@westie thanks! @Dimitrios-Kanellopoulos any clue on when this might come for the 9PP? I was perhaps under the wrong impression that both SV and 9PP would get the update at the same time.
-
It’s Friday morning here in Australia still no updates for my vertical ?
-
@gone-troppo as always, all updates are phased.
-
Thanks mate so how do we know when the update is ready does something pop up
on the watch or app? Or is there something I have to do manually to trigger it ? -
@gone-troppo you’ll see the update in SA (option wheel on the sync screen)
When it’s uploaded in your watch you’ll find it in settings/general/update. If you have activated auto update, and if you don’t launch it manually, it should be installed at night if you have enough battery -
Installed the update this afternoon… seems to be everything ok… feels smooth. I did my first run this evening, maps are working, I had no problems. The new UI is little bit different, but I think after same days it will be cool. Until now I can say it‘s a improvement
🤩 -
@altcmd It will come. We were working hard on it. I don’t think I can provide you with an exact date but it should be soonish.
-
Hi everyone, I downloaded the software update to my vertical titanium, and after tapping on it to start the install and a countdown to 0 the watch is now completely dead. It doesn’t react even to a soft reset. (Before starting the update the battery was at 75%)
Any ideas on what could I do?
Thanks -
@Tieutieu said in Software release 2.30.26:
I’ll try to delete and set again my walk mode.
Did it work out for you? I still have the issue. Even after I created a new custom sport profile
Suunto Vertical Titanium Solar
OnePlus Nord 4 -
My watch has been stuck in “The device is being restored to a safe state” loop for the past 6 hours after trying to update - has this happened to anyone else?
-
@surfboomerang nope, it didn’t worked for me too.
That’s strange my custom hike is ok, I can unpin ohr, but walk still not even after having recreated it. My climbing custom is also concerned, can’t unpin ohr. -
@Tieutieu is there an Option to downgrade back to the older Firmware!? When yes how to do this?
-
@GiPFELKiND said in Software release 2.30.26:
@Tieutieu is there an Option to downgrade back to the older Firmware!? When yes how to do this?
I don’t know and don’t need it. The new firmware seem quite ok to me !
But maybe it is possible somehow -
@Dimitrios-Kanellopoulos said in Software release 2.30.26:
WHR FW update
This was a nice surprise and seems to have made a noticeable difference in the daily HR readings I’m seeing (only one day in). Previously, my HR always measured somewhere near 100 bpm every time I looked at it, resting or not, as though 100 were the default while it looked for an actual reading. Today, I’ve observed some reasonable numbers. Anyone else?
-
After the update failed, I ended up doing a soft reset and that seemed to fully reset the watch (lost all historical data on the watch, which is a bummer, but oh well - at least it works now). Now it’s saying in the Suunto App that the new software package (2.30) has been downloaded, but the watch is saying it’s up-to-date (with 2.25). Tried hard resetting the watching, forgetting it in the app - nothing seemed to solve it.
