Software Update 2.30.32
-
@Александр-Даниленко My experience too with similar amount of activity. I have discharged it completely and left it to charge for 2 hours, it recalibrated the % to a more accurate drainage by hours/days but didn’t improve the overall capacity.
I have done a hard reset 2 days ago as I was experiencing completely unusable sleep data since the update too. I’m monitoring how things evolve over the next few days and will report my findings. I also reduced the Brightness to medium, turned of Standby and Raise to wake to Low.
One thing for sure: the sleep summary is delayed (ex: today my alarm rang 6:55, I woke up, came to work, now it’s 08:45 and my summary just showed up on the watch. Trying to understand the new algorithm a bit better before making conclusions, but it does seem to not ‘live well’ with movements and nights: typically waking up to go to the bathroom and back to sleep; last night the tracking just ended less then 2 hours into my night as I went to the bathroom, no more tracking later on.
I’ll follow back on my findings next week
-
@Александр-Даниленко no need to discharge completely.
Down to around 20% is enough.
Just give it a cycle and then re-evaluate.
If that has not happened since the update any judgment on the discharge rate is of no real use.
Cheerst6, S6, Elementum Terra, Ambit 3 Sapphire, Spartan Ultra Copper, Traverse Alpha, S7 Graphite LE, S9B Ambassador, S9P Granite Blue Titanium, S9PP Titanium Sand, Vertical All Black, Race Titanium Charcoal,
Race S All Black - TI Canary - Titanium Courtney -
@RaDeck For the sleep summary, its always been like that (for me at least) unless you touch your watch when you are fully awake (for example, when eating your breakfast) it won’t display the summary for a long time
-
@Egika , just a question:
And how is the “re-calibrate” done? Simply by leaving the watch fully discharged and then recharging it for more than 2 hours?
Thank you.
-
@Egika I did it then - discharged to 20% and charged to 100% once.
-
@Elipsus ok. So I’ll try interacting with my watch once I’m awake and see how it reacts / when the report is shown. Thank you!
-
I don’t what is going on, but the watch seems kidding me…
And this is not the 1st time for the last days when sleeping time was completely off.
I would like have an opportunity to edit sleeping time for such cases …
-
@Александр-Даниленко I don’t know since the update I have quite good sleep results. I have the HRV on, 24/7 on… basically everything is on
But my results seem to be in line what I would expect based on my feelings. Only once during the night my OHR stopped working and I had to reboot watch in the morning. -
@Zdeněk-Hruška I also have everything on
-
@Egika Thanks for the tip. Well I did it and I still have the feeling that the battery is draining faster outside of exercises. Of course, I have no data to validate that it could be only my feeling. But I don’t know I really noticed that before I read similar cases here. I will keep an eye on it
-
@Egika I bet it’s absolutely a software problem not a hardware, calibration etc. Draining has increased only in “standby” mode. And it’s literally a joke - 16% in less than 2 days of laying on the table and doing something (but what?) in the background
Dear Suunto, make 9pp great again!
-
@false I just wand to make sure that we start betting after ruling out the obvious:
- battery calibration after update
- OHR sensor firing away while watch is lying on a reflective surface
-?
-
2- ohr is switched off as well as any other sensors/metrics etc. I don’t use the watch between trainings
1- Please tell me why is it obvious? Because for me it’s not. And how could you explain increased consumption only in certain modes, I guess if it’s really needed to be calibrated it will affect all modes without exception. It’s ok to ‘calibrate’ li-ion once in a couple of months but this shouldn’t have anything with software updates. It’s not the first update for 9pp and I’ve never done (specially) calibration after any of them. So yeah, I bet standby mode is broken.
PS: now I’m on a vacation without watch charger (as I usually do) from today I have to switch the watch off after every training just to be sure I can track my run in a few days. Nice. Reliable.
PPS: if calibration is really needed after every update then we (users) should hear it from Suunto release notes not from other users on the forum
-
@false said in Software Update 2.30.32:
2- ohr is switched off as well as any other sensors/metrics etc. I don’t use the watch between trainings
thank you for the information
1- Please tell me why is it obvious? Because for me it’s not. And how could you explain increased consumption only in certain modes, I guess if it’s really needed to be calibrated it will affect all modes without exception.
Correct! Maybe I did not read properly.
It’s ok to ‘calibrate’ li-ion once in a couple of months but this shouldn’t have anything with software updates. It’s not the first update for 9pp and I’ve never did (specially) calibration after any of them. So yeah, I bet standby mode is broken.
Sometimes the missing calibration after software updates is more obvious, sometimes not. That BMS is reset after some update is confirmed knowledge from Suunto devs. I never did calibration as well, as it levels out automatically. It is just good to know that a quicker dropping charge displayed after an update is to be expected.
PS: now I’m on a vacation without watch charger (as I usually do) from today I have to switch the watch off after every training just to be sure I can track my run in a few days. Nice. Reliable.
PPS: if calibration is really needed after every update then we (users) should hear it from Suunto release notes not from other users on the forum
Not needed. Just needed if you want to rest assured that a higher discharge rate after update is nothing bad. And this is why I begin with the “obvious”. This is like the tech support hotline asks you first if the power plug is plugged in and you of course are miles ahead with your own assessment of the situation. Still for some people calling, the plug indeed is not plugged
-
Hi, I rarely take off my watch but today while I was in the office, I put it on the shelf next to me and noticed that it doesn’t go to sleep (display all black) anymore after the usual time of inactivity. I’ve tried a soft reset but does not help. Anybody else?
-
@robis Reported and known by Suunto.
-
So the second time after the latest update my OHR stopped working during the night and I had to reset the watch in the morning. Does anybody else has a similar experience?
-
OHR stopped working yesterday, but right after nightsleep. Statistics from the night were already a littlebit odd (too short) and later I noticed that OHR was not working anymore. Softreset helped and last night statistics are more accurate also
-
I have no idea what is going on now. I put the watch on a drawer before going to bed and noticed the display was always on. I noticed the battery was low (8%), put it on the charger, this morning the display was still on. Standby and rise to wake are off. I am staring at the watch now and it’s still on, it never goes off anymore and reboots do not help. Anyone else experiencing something similar?
P.s. I have noticed the same behavior with the Vertical once (same scenario, low battery) and I am seriously thinking about moving to a different brand now.
-
@tomasbartko I asked for a few posts above. It’s a known bug.
