S+ Race pacer
-
@DF130 not sure watches with the old interface support this particular app
-
@herlas right now the sync is very slow because of the apps, but I hope this will be solved in the future
-
@isazi S9
-
@forde-mic not sure if the S9 supports these settings via the app, but I believe that @Raimo-Järvi should know
Watch: Suunto Vertical Ti
Blog: isazi's home
-
@isazi S9 and S9P don’t support settings and therefore Race pacer app should not be enabled for them in SuuntoPlus store. We will fix that, I’m sorry for the inconvenience.
-
I wish the setup was more flexible. With hours, minutes and seconds. With current configuration how can I set overall time like 30 mins 40 seconds? -> 30.33 mins? And 30 mins 27 sec? Not pretty obvious and easy to use.
Also, it would be nice to see km by km pace plan after calculation -
@false were you able to test this? Wondering if we really have to do the math for the seconds like that
-
@herlas I was able to set XX.5 mins in the app but since the watch shows a gap between you and ‘pacer’ in meters it’s hard to check whether such hack works or not.
Anyways, despite ‘race pacer’ is useful (on paper), in general, this feature requires further improvements because it doesn’t cover so many use cases
-
@false It looks like you haven’t understood the function of the app correctly. The difference (gap) between your actual time and the targeted one is shown in minutes and seconds at the top of the screen. The distance shown at the bottom of the screen is the remaining distance of the race.
-
@soisan I’ve understood it right but I did a mistake when I was writing about it
It was meant to be
I was able to set XX.5 mins in the app but since the watch shows a gap between you and ‘pacer’ in MINUTES it’s hard to check whether such hack works or not.
Which means - since a watch doesn’t show target PACE for the desired time I can’t check whether the hack with decimals works or not. It requires to do some maths on the run which is hard
-
@false If you want to check that without any calculations, you can record a manual lap with the lower button while the gap is 0:00. The lap pace is the same as the target pace. At the beginning of an activity, getting a null gap shouldn’t be difficult.
-
@soisan That’s right! Or check your pace when the gap is 0 - I didn’t think about it
Anyway, it would be much much better to see all this stuff in the app, incl. time settings within hours, minutes and seconds
-
Agreed, specifying minutes was a good starting point for this awesome S+ app that was long time overdue on Suunto
.Please pass along this feedback to the concerning team/dev about expanding this S+ app to include hh/mm/ss in the configuration,
-
@Raimo-Järvi FYI I was also allowed to install on my S5P but I’m guessing, like the S9P it doesn’t support config so also isn’t compatible. When I attempted to use the app during a workout the screen briefly showed a few red error blocks and then switched back to the previous screen.
-
Just an update on this. After installing the app and finding it didn’t work I then found that it ‘broke’ syncing for all other suuntoplus apps. I was unable to update, add or remove guides or apps in any way. I tried a restart and it didn’t fix things so tried a factory reset. This basically ‘bricked’ the watch and I had to resort to using SuuntoLink to reinstall the firmware from scratch - which thankfully did work.
-
@far-blue You’re correct, it shouldn’t be available for S5P either. We will fix it, I’m sorry it has taken so long. Thank you for the feedback, and apologies for having to reinstall your watch.
-
@Raimo-Järvi No worries and no criticism, I mainly posted the update in case other people hit the same problem
-
@Raimo-Järvi can you advise if it’s planned to update this awesome S+ app to include goal time input in following format hh:mm:ss?
Even the links listed in the app description such as below, allow you to enter in such format to calculate the pace :
Any comments would be greatly appreciated
https://www.runnerscalc.com/running-negative-splits-calculator
-
@far-blue said in S+ Race pacer:
Just an update on this. After installing the app and finding it didn’t work I then found that it ‘broke’ syncing for all other suuntoplus apps. I was unable to update, add or remove guides or apps in any way. I tried a restart and it didn’t fix things so tried a factory reset. This basically ‘bricked’ the watch and I had to resort to using SuuntoLink to reinstall the firmware from scratch - which thankfully did work.
Phew, what a nuisance! I hadn’t put that S+app to use yet, but I was thinking of doing so… and now I’ve had a scare.
What model of watch did this happen to you? Or can it happen with any model (which I don’t think it can)?
-
@enriqueescoms It should work fine for the S9PP, the Race and the Vertical. These watches support S+ apps with configuration options.
The problem is with the S9P and S5P and similar older watches that don’t support configuration options in S+ apps. In my case it was with a S5P.
