Software Update 2.43.8/.12 (2025 Q2)

[safari]

@Max-maxilifeguard If you’re talking about installing an FW,

Go to Settings > General > About

Scroll down to the bottom.

Hold down the bottom button on your watch.

Debug mode will appear.

Here, you’ll see the FWs in the “Select OTA Packet” section.

Remember, your watch’s battery should be at least 50%.

[Max maxilifeguard]

@safari thanks, but the problem is the watch is lock, i can’t unlock to used. I wonder is its possible to do it from the app

[Milan Šádek]

@Max-maxilifeguard there is no other way to recover a bricked watch than sending it to the Repair center. Mine got flashed and sent back to me within 48 hours. Good luck with your device!

[safari]

@Max-maxilifeguard In this case, the repair center…

[sky-runner]

@maszop said in Software Update 2.43.8/.12 (2025 Q2):

Now, not only are there no contour lines, but there are also no paths or trails.
Thank you Suunto Team.

And as I mentioned earlier in this thread it is even worse when using imperial units because everything disappears at 0.2 mile scale, which is just 320 meters.

And at 500 ft (150m) scale trails are so thin on Race and Race S that they are almost invisible to my aging eyes unless I stop and steady the watch. With this change, maps are no longer useful to me.

Can you see the trail going down from the center of the screen on the picture above? I usually can’t. And it is even worse on a smaller Race S screen.

[GiPFELKiND]

@sky-runner hey @sky-runner you can downgrade

[Squirrel]

@Pavlas said in Software Update 2.43.8/.12 (2025 Q2):

The dissatisfaction over the new maps has been mentioned several times already. Especially the disappearing paths when zooming out more.

Consider creating a thread about these map rendering issues, since you have a good comparison pictures and apparently 2 watches as well.
This way, it would not get drowned down among other things in 2.43.8/.12 and will be useful for later firmware releases as well.

[Max maxilifeguard]

@safari said in Software Update 2.43.8/.12 (2025 Q2):

@Max-maxilifeguard If you’re talking about installing an FW,

Go to Settings > General > About

Scroll down to the bottom.

Hold down the bottom button on your watch.

Debug mode will appear.

Here, you’ll see the FWs in the “Select OTA Packet” section.

Remember, your watch’s battery should be at least 50%.

I performed this procedure. When I opened the OTA packet, the odd thing was that it had two versions: the latest 2.43.12 and the other NORMAL 2.43.8. I selected that one and restarted. Then I updated again to the latest software version. I checked the OTA packet again, and this time it only showed the latest software version. I hope that’s the solution.

Thanks for the help.

[maszop]

@sky-runner said in Software Update 2.43.8/.12 (2025 Q2):

@maszop said in Software Update 2.43.8/.12 (2025 Q2):

Now, not only are there no contour lines, but there are also no paths or trails.
Thank you Suunto Team.

And as I mentioned earlier in this thread it is even worse when using imperial units because everything disappears at 0.2 mile scale, which is just 320 meters.

And at 500 ft (150m) scale trails are so thin on Race and Race S that they are almost invisible to my aging eyes unless I stop and steady the watch. With this change, maps are no longer useful to me.

Can you see the trail going down from the center of the screen on the picture above? I usually can’t. And it is even worse on a smaller Race S screen.

I think standard outdoor maps should have thin paths like these (like on regular maps). Unlike the current update, where paths in the city look like highways.

Additionally there should be an additional version of the map (something like High Contrast), where everything would be much more clearly marked (something even excessively so), for those who need such a version.

[sky-runner]

@Squirrel said in Software Update 2.43.8/.12 (2025 Q2):

Consider creating a thread about these map rendering issues, since you have a good comparison pictures and apparently 2 watches as well.
This way, it would not get drowned down among other things in 2.43.8/.12 and will be useful for later firmware releases as well.

I’ve just created a new tread

[sky-runner]

@maszop said in Software Update 2.43.8/.12 (2025 Q2):

I think standard outdoor maps should have thin paths like these (like on regular maps). Unlike the current update, where paths in the city look like highways.

Additionally there should be an additional version of the map (something like High Contrast), where everything would be much more clearly marked (something even excessively so), for those who need such a version.

Here is the problem. Suunto Vertical has 240x240 resolution if I am not mistaken, so thin paths look generally OK. Suunto Race and Race S have much higher resolution, so thin paths are nearly invisible. I have very hard time seeing trails at a 500ft zoom level when running, even when using high contrast map theme. If I stop and steady the watch, it is easier, but borderline impossible while moving. The last zoom level where I can see trails well is 200ft, which is just 60 meters, which covers only 20-30 seconds of running. Something has to be done specifically for Suunto Race and Race S.