Updates for V1

[cosme.costa]

@plopes73 I have read somewhere, I do not remember where, that there is a bug in the widget that do not shows the real solar harvesting, but it works correctly. This bug has not been adressed yet, could be this?

[sartoric]

@cosme.costa
there is a refresh bug in the history widget, but the real time view shows the current state correctly
Mine goes from idle to maximum… depending on the sun ofc
in these days, almost always at maximum

[plopes73]

@cosme.costa Could be, I’ve not notice differences in battery, but then again, solar harvesting do not charges battery, only helps a bit. However my widget only show idle and minimum (a very small colored dot in the middle of the scale). Also the 15min bars are always on minimum, on these clear days they were at least half way after some runs. Hope that is true, only a bug in widget Cheers

[plopes73]

@isazi On mine, the wiget doesn’t work as before and as far as I read, in the last firmware update solar harvesting was not in scope, but in my watch it’s not the same, at least what’s visible on the widget. I have never had an issue with any update, not even some reported issues with battery and all that That’s why I found this strange ;). Cheers

[plopes73]

@sartoric On my watch not even the live widget (on the watch face) shows more than minimum, just idle and minimum, even on direct sunlight. Maybe I need to do a hard reset (the one with 60 seconds on the charger), soft resets didn’t work. Thank you for sharing that info. Cheers.

[isazi]

@plopes73 unfortunately you would not be the first to have some hardware issues with the solar harvesting module. If your watch is still under warranty, contact support to have it checked and possibly repaired.

[babychai]

@plopes73 do you using screen protector?

[LitchiMonster]

@plopes73 this happened to my watch, I sent it in. They checked the solar module, agreed it wasn’t working, and they replaced the watch. Unfortunately the original was made in Finland and the replacement watch made in China. Oh well, it works now.

[Egika]

@LitchiMonster said:

Unfortunately the original was made in Finland and the replacement watch made in China. Oh well, it works now.

So maybe this turns from unfortunately into fortunately

[plopes73]

@babychai No no, never used screen protector. Suunto saphire glass is very good, no need to protect it with a weaker layer IMO. But I think it’s a hardware issue, watch is not in warranty anymore, but I can live with it, until Suunto Vertical 3 release :). Cheers.

[ChristopheRamon]

@Tieutieu said:

The only major issue for me is that climb guidance as not been updated like it has been on SRs, SR and SV2 SR2
It’s still almost unusable on SV1 because extra zoom level on current segment is not there when POI are on the route.
This has been adressed very nicely on my SRs, but it’s a big miss on my SV1.
For all other new potential new features (tide app and so…) i perfectly understand that SV1 comes to it’s limits, so minor/bugs corrections will be fine now.
It’s still my favorite and I have not decided to go for a SV2 (will wait for a further generation)

Fully agree with you. Let’s believe that adding back the extra zoom level on current segment when there are some POIs will not be that difficult. Much easier at least than adding all these new features related to maps ! Come on, Suunto developers

[stromdiddily]

@ChristopheRamon even without the climb guidance zoom levels, you can’t add “Ascent to Waypoint” as a data field on the V1 which would be enormously helpful.

[vminaev]

Vertical V1 is not working correctly with Stryd.((

[thanasis]

Hi Team

any news here? at least let’s have some visibility of whether anything changed or not, would be really beneficial.

thanks

[martintrail]

@thanasis No one will answer you. Certainly no one officially. That’s just the way it is.

[VoiGAS]

@martintrail Yes, but I think its good to keep the topic active. Last info was that the V1 isn’t discontinued, but April and July Updates just didn’t come. Now with end of September another quarter ends and we will see if a new Update arrives - for the V1
Still hoping

[martintrail]

@VoiGAS There are rumors that Q3 will likely be delayed and shipped together with Q4.

[2b2bff]

@martintrail would be great if Suunto could just have a short message on their blog “Sorry guys, for reason xyz we have to delay Q3 and ship it together with Q4.”, wouldn’t it?
I mean customer communications and so. Would help for all the “is it there, yet?”-people.

[André Faria]

@2b2bff said:

@martintrail would be great if Suunto could just have a short message on their blog “Sorry guys, for reason xyz we have to delay Q3 and ship it together with Q4.”, wouldn’t it?
I mean customer communications and so. Would help for all the “is it there, yet?”-people.

I guess most companies don’t share that kinda of stuff. Also if I recall correctly suunto doesn’t have a public plan aobut releases , like garmin for example.

[2b2bff]

@André-Faria I know there is no exact plan but in the past there have been quarterly updates all around. The release videos of Janne have been delivered only after the release has been made, but on the other hand he talks about updates coming later for specific device models.

So, why not publish a short video - if that is the known outlet - about Q3, with “sorry, will come together with Q4”. They don’t even have to name the real reason. “Release is not up to our quality standards, yet” is as good as any reason.
In my books this only will increase credibility instead of being tight lipped for three months.