Software update 2.16.26 June 10th 2021

Egika

@dimitrios-kanellopoulos said in Software update 2.16.26 June 10th 2021:

The standby light is not required

Ok, now I got it.
The standby light switch needs to be on for Raise to wake to work.
Standby will actually be off and only come on when raising the watch.
I understand this implementation now

Still missing the two finger toggle tap…

Dimitrios Kanellopoulos

@egika try the shortcut from the watchface long press.

Egika

@dimitrios-kanellopoulos said in Software update 2.16.26 June 10th 2021:

@egika try the shortcut from the watchface long press.

I’ve seen it.
Still it is two long buttons plus selection of the menu item.

I often used the two finger tap if I received a message and am in the dark.
As long as the message was displayed I could toggle the backlight on and off. Super easy and quick. The light would stay off otherwise.
In darkness it is difficult to get the shortcut right as long as the light is not on yet…

Dimitrios Kanellopoulos

@egika yeah I get it.

Prenj

Is baro trend arrow gone in outdoor watchface or does it just need some time to catch up?

halajos

@prenj as the firmware update clears all data, it needs some time to collect some for trend analysis

surfboomerang

@prenj Normally it takes a couple of hours

inkognito

@egika But, the light will now turn on with every button press and it will even turn on automatically on every notification (messages etc.) unless you have DND on. So, you don’t need to get that shortcut without backlight.

I really loved the toggle mode on my Spartan Trainer with a dedicated button press for backlight. But on Suunto 9 it wasn’t very practical for me. To check the time at night, one had to wake the touchscreen by a button press and then tap the screen with two fingers (which usually failed for me like three times before I managed to turn the light on). So I switched to automatic backlight (turns on with every button press), but from time to time I was missing the ability to turn the continuous backlight on easily. Now I have both

Tomas5

@Dimitrios-Kanellopoulos with suunto 5, Will I still be able to toggle backlight with long press of upper left button or this functionality is removed ?

Dimitrios Kanellopoulos

@tomas5 to be honest I don’t know but I would expect that it ain’t removed. I’ll check with evening with my s5

Egika

@inkognito thank you, I got it.
Think I will have to live with this, as it was necessary to streamline SW to the Peak model which has advanced backlight features.

Anyway, those new possibilities are not so much for me. I like no backlight at all most of the time (partly to save battery, partly not to disturb others).
I like no light with every buton press, nor with every notification. Just with notifications and the toggle tap.

Let’s finish this as it can’t really be resolved, and check out some other new features

DMytro

Great update, thanks suunto! That’s a lot of features btw.
Does the altitude also gets “corrected” using snap to route?
This would make my non-baro hill repeats so much better XD

isazi

@дима-мельниченко nope. I agree it would make sense, and I asked for this.

DMytro

@isazi oh, I see. Well, maybe next time!

DMytro

I didn’t find it in the manual: what does this colourful circle in the new watchface mean?

A Former User

For using snap to route do not abuse it. No loops (ie track and field) and no reverse routes.

OK, so if I have 4-5 mile trail loop I intend to run 2-3 times, will snap to route work in this case? Or a 1.25-mile loop in the park that I intend to run, say, 8 times?

ChrisA

@дима-мельниченко as far as I understand it, it shows your Resources (green) steps (blue) and calories (orange) …

DMytro

@chrisa ah, ok, that makes sense. Thanks!

Dimitrios Kanellopoulos

@nickk you need to build a route with the number of loops you expect at the park. Not one route you are going to restart plenty of times. I am not sure, though have not tested the loops. I just know what I got told.

A Former User

@dimitrios-kanellopoulos OK, that sounds reasonable but let me test the abuse version first, i.e. running same loop multiple times and see what happens

Perhaps, if creating multiple loops is a requirement we can get a Loop feature in the route creation tool in the app? You let the app close the loop and then loop automatically a specified number of times?

Because doing it manually on a 5-mile loop with plenty of turns is an exercise in frustration. It would be easier to edit GPX file directly.