New to S9Peak from S9B

[TheGuyFromTheSummit]

thanks for the replies!

It looks like, I stick to my S9Baro

[isazi]

@theguyfromthesummit similar to @surfboomerang I only use the 7 data fields in mountaineering cause I am not going to fiddle with my watch, and want everything at once. I find the readability good, but my speed is low.

[MiniForklift]

@isazi Same, I only really use 7 data fields for when I am climbing or if I am doing an activity where the speed is going to be slow. Most of my main screen have 3 fields or 4 at the maximum, easy to read when you’re flying down the side of a mountain

I just find the thought of dropping from 50mm to 43mm a bit too much of a jump. One of my friends is waiting for their S9P to arrive so I’ll check theirs out once they have it

[TheGuyFromTheSummit]

How can you have enough with only 4 fields

I always use 7, no matter if biking, trailrunning or hiking, I just don’t like to switch between screens.

[Brad_Olwin]

@theguyfromthesummit said in New to S9Peak from S9B:

How can you have enough with only 4 fields

I always use 7, no matter if biking, trailrunning or hiking, I just don’t like to switch between screens.

How can you need 7 fields??? Mostly I need ascent and distance, I don’t understand how the data are of any use when running/MTB. When road cycling I would use cadence, speed, distance and power, not much else. I have 4 fields and one screen for everything but races where I use 2 screens with 3 fields each on both S9P and S9b.

[Łukasz Szmigiel]

@brad_olwin etas perhaps. I use ETA / ETE for end and POI, sunrise, sunset and it’s 6 fields already. But that’s for hiking or a second screen for long trail runs in case I get lost or something unforeseen happens.

[Efejota]

@brad_olwin In my case, in addition to what you use, I also put sunset, temperature, average pace or speed, vertical speed and things like that depending on the sport. In most of the cases (unless sunset, TBH) I must confess that I could live without those data . But, what the heck, I have a S9P, I must have tons of information at any moment!!!

[Efejota]

@theguyfromthesummit I rather switch screens than having my watch constantly reminding my age when trying to read those tiny numbers

[Brad_Olwin]

@łukasz-szmigiel So if you engage SuuntoPlus Weather and have a route loaded, an ETE/ETA field and Sunset is already there. Why I try to keep the data in the watch simple.

[Łukasz Szmigiel]

@brad_olwin valid point. But it’s unavailable in S5 and besides - one might want to limit screen switching and S+ requires to shuffle the screens.

Btw. is it possible to switch screens to the left in S9 series as there’s no dedicated back button?

[DMytro]

@łukasz-szmigiel only via touch

[Łukasz Szmigiel]

@dmytro well, I would have to change my habits and redesign the screens if I had S9 then. I often jump between navigation and the screen before it. I’d have to cycle all the way forward if on 9?

[DMytro]

@łukasz-szmigiel sadly so. It’s fine with me as I rarely look at the data other than hr and duration, map - so only two screens basically.

[Brad_Olwin]

@łukasz-szmigiel No, it is easy to customize a battery mode with touch so you can scroll back and forth on screens.

[Łukasz Szmigiel]

@brad_olwin but you have to enable the touch in custom battery mode, right?

[TheGuyFromTheSummit]

@brad_olwin Usually I have:

1. ascent
2. altitude
3. distance
4. pace
5. heartrate
6. vertical speed, barometer, ETA, sunrise or sunset.
7. duration

Field No 6 is more or less just to fill the field. But sometimes sunrise and sunset for multi day tours

But playing around with the peak might get me switching to 2 displays with 5 fields. this watch is so light and small, it is amazing

[surfboomerang]

@łukasz-szmigiel Correct.
I use it for a couple of sport modes, but I would rather see that Suunto implement this for buttons too.
The big problem is probably the number of buttons available All the buttons already have dual actions assigned to them for press and press-and-hold.

[Brad_Olwin]

@theguyfromthesummit said in New to S9Peak from S9B:

@brad_olwin Usually I have:

1. ascent
2. altitude
3. distance
4. pace
5. heartrate
6. vertical speed, barometer, ETA, sunrise or sunset.
7. duration

Field No 6 is more or less just to fill the field. But sometimes sunrise and sunset for multi day tours

But playing around with the peak might get me switching to 2 displays with 5 fields. this watch is so light and small, it is amazing

I have for races
Screen 1

1. Lap Ascent
2. Lap Pace
3. Vertical Speed
   Screen 2
4. Ascent
5. Vertical Speed
6. Pace
7. Distance

The altitude profile will show altitude and HR is in the zone ring, I don’t need exact HR, just zones. The second screen will show duration at the top. I have alarms set for Sunrise/sunset. If needed I run SuuntoPlus Weather, which has sunset time and ETE/ETA.

[TheGuyFromTheSummit]

@brad_olwin
This actually is a completely different but nice approach!

I have to test it.

thanks

[Brad_Olwin]

@theguyfromthesummit said in New to S9Peak from S9B:

@brad_olwin
This actually is a completely different but nice approach!

I have to test it.

thanks

I use the lap intervals for aid stations so I know whether my timing is ok and when the cutoffs are. I make a jpeg/png of a spreadsheet for aid stations/timing and use that as the Lock Screen image on my iPhone. That way, I do not have to open my phone but just turn on/pull out of my vest and I can check times against the watch.