Real world data
-
Today I had a strange behaviour of my S9p during multisport mode.
First I was cycling for about 20 minutes, then I switched to customised running mode by long pressing the upper button (pushing my bike with one hand), wondering why the distance and duration from cycling were displayed unchanged (normally when switching the values start from zero) and only pace and HR actively changed in running mode.
Then I switched back to cycling for few seconds to make sure I had changed modes correctly and switched back to running mode, but the display remained as before. After about 2km I switched back to cycling and rode my bike, but again the distance and duration remained unchanged, only speed and HR showed current values.
My last attempt was to press manual pause and start again without finishing the complete recording, only then distance and duration continued to count.
At the end of the recording, the complete part of running was missing, the entire multisport unit consists only of cycling.
What could be the reason for this behaviour?The other days before I had no problems with multisport.
-
For those interested
Suunto 9 peak gps+Glonass
https://www.suunto.com/move/andrfaria640/6102dfdf6d6a6919c8c94747
Garmin 945 fw3.07 gps+glonass
https://connect.garmin.com/modern/activity/7211028776Altimetry on Garmin doesn’t seem correct. I will try to calibrate/ see if there is any setting that can affect it.
-
Has anyone else tested pool swimming yet?
It is strange that in the logbook and in SA no total distance is shown but only intervals.
So I have to calculate the total distance manually and edit the unit in SA.
I used the basic profile with standard settings and S+ off. During the exercise I could see the total distance correctly.Is this a special issue of S9p or of the current firmware 2.16.26 in general?
-
@wotus do you have an sa link ?
-
@dimitrios-kanellopoulos said in Real world data:
@wotus do you have an sa link ?
https://www.suunto.com/move/steffen10341/6102c3cfd2b909358441e577
-
@wotus I suppose now it’s too late you edit d the distance manually?
-
@wotus if possible on the next please try not to edit it.
-
@dimitrios-kanellopoulos Yes, the distance data field was zero like in the logbook and then I edited it.
-
Here are a couple quick thoughts after using mine since about mid-june:
-i love this watch! huge improvement for me over the 9, especially the weight!
-OHR is accurate for me, only within a couple beats of HR strap. That’s a first! One caveat: the strap has to be somewhat tight on my wrist.
-My trail runs seem to be getting longer distances than they should. For example, OCC ended up with 36mi/57.6km. Not a huge discrepancy but it should have been 56km. Similar experience in another race.
-Pool swimming has been spot on but after the last lap I give it an extra few seconds to think before ending activity. Otherwise it cuts out the last pool length for whatever reason.
-Cycling is great. I don’t like using wrist watch for cycling but just tested it out for the fun of it.
-Battery life overall is much better than the 9 for me and i really appreciate the fast charging.
-
On my first openwater swimming with update 2.18.18 no temperature was measured. The custom datafield during activity was blank “–”. The logbook and SA entry don’t have a value for temperature. I guess it was about 16-17 degrees celsius. Before and after the workout temperature in watchface mode is showing normal. What was going wrong?
https://www.suunto.com/move/steffen10341/615872fdf76eab3f359fc78a -
@wotus After several unsuccsessful tries I found a workaround forcing the watch to measure and record the temperature in openwater swimming (basic and custom exercise), with which all other exercises have no problem.
The only way I found is to activate S+ Weather - Insights before the start.
But even then, the realtime temperatur data field shows no value “–”.
Only if I switch the display to the Weather screen and then back to my first view, the real temperatur value will be shown and appears then in the logbook and in SA.
Can someone confirm this strange behaviour of missing temperatur in openwater swimming which didn’t happen before the last firmware update?
