SOFTWARE UPDATE 2.35.34 Q2

duffman19

@The_77 When it showed uphill instead of downhill, were you on an overlapping section of the route? I’m trying to figure out if that is the cause.

sartoric

I’ve never used tbt before, so I’m just giving it a try with the new Fw.

found this bug that I’m almost sure it’s already been reported, but , anyway …

kinda straight back and forth route, with a small loop on one end, actually a lasso
got indication to turn left on my way back, even if I should go straight.

detail, I paused almost at the middle of the route.

duffman19

@sartoric It looks like all the turn arrows are backwards. It’s giving you directions as though you are coming from the opposite way (from left to right on your watch face). But the long, light blue arrow is correct. This looks like another case where some navigational tools think you are following the route backwards, and others think forwards.

I tried to explain my experience here: https://forum.suunto.com/post/148013

The_77

@duffman19 no right at the start, but for some reason it contains uphill in it…

Iggge

I think i have found a bug. After several days now my Vertical shows 100% less steps than before.

My Samsung shows 7000 steps. My phone haven’t been with me all day either.
My Vertical 3700 steps.

My Vertical don’t count steps if;

I have my hand in the pockets
have something in my hand (like a bag from the store)
Using a cart (Or similar)

I hope it will get fixed soon.

Tami999

@Iggge said in SOFTWARE UPDATE 2.35.34 Q2:

After several days now my Vertical shows 100% less steps than before.

And i think its lots more accurate than before. At least it doesnt count steps when i take my hands in the air.

wurzlsepp

Another thought concerning the map and the new stop screen: if autopause triggers now while on the breadcrumb map on 9PP, i can still see the map and see where i have to go next; that is great!
However, it always reverts the zoom level to 100 m once i start again. I would prefer if the watch always sticks to the zoom level set manually instead of defaulting to some value during manual/automatic pause

Tieutieu

First big test of climb guidance today (10h45 trail running race).
Works great.
But : my SV was at 98% charge. It ended at 75. Seems very high compare to previous fw. Maybe I need battery to achieve a cycle for new calibration ?

Stefano M64

@Iggge said in SOFTWARE UPDATE 2.35.34 Q2:

I think i have found a bug. After several days now my Vertical shows 100% less steps than before.

My Vertical don’t count steps if;

I have my hand in the pockets

have something in my hand (like a bag from the store)

I experimented a similar behaviour with my Race (previous fw) by walking with hiking poles, it counted roughly half of the steps shown by smartphone. I didn’t still tested with new firmware.

Iggge

@Stefano-M64 Good to know I am not the only one. Have been active all day and still under 5000 steps. My phone is at 12.000

pilleus

@Iggge

Use a pedometer to check your real steps. The steps tracked by a smartphone are not really exact.

Iggge

@pilleus my own experience are that smartphones are better when it comes to counting steps. My smartphone are always in a pocket located on my left leg and therefore don’t get anything else then steps because of it’s location.
Right now my phone shows 21000 steps, and my Vertical 11.000.

And I have been running today (10 km) and been walking around town for about 2 hours.

Mitch9

@Mitch9 said in SOFTWARE UPDATE 2.35.34 Q2:

Could it be that the vibration on SV is a little bit softer or smoother after the update?

Noone else recognized this?

GiPFELKiND

@GiPFELKiND said in SOFTWARE UPDATE 2.35.34 Q2:

Had very scary TSS and other values today… Was swimming in the sea actually and suddenly after this Look… 🥴🥴🥴 Someone Something like this!? Whats going in? TSS Yesterday about 700, ATL 104, CTL 102, TSB about -55. But look on the watch graph today

Someone have totally wrong values after the update, too?!?!?!

isazi

@GiPFELKiND I have seen the screen with 999 on another person watch with previous firmware, it was the first time ever I’ve seen something like this. If you still have this, send logs and PM me.

safari

Can improvements be made regarding the weather?
Automatic weather sync when suunto app is open on phone.
I cannot change the unit of measurement for wind speed. It turns out m/s, I want km/s.
thanks

zewen

@Tieutieu same situation happened to me

Egika

@safari said in SOFTWARE UPDATE 2.35.34 Q2:

Can improvements be made regarding the weather?
Automatic weather sync when suunto app is open on phone.

This should currently be the case. Automatic weather sync is happening.

I cannot change the unit of measurement for wind speed. It turns out m/s, I want km/s.

km/s? That will either be a veery small number or a super hefty storm…

stromdiddily

Anyone post this one yet? Will get half a display of notifications then it moves to black screen

babychai

@stromdiddily i have this issue too. it seems like struggling to show the messages