SW update 2.37.34 Q3

Egika

@Boss-Hogg-450 said in SW update 2.37.34 Q3:

Whilst the improvements to the Turn-by-turn display logic are nice. Does anyone know if there is an option to Disable the “data tooth” on the map screen? If TBT is not being used, not “having” to have a data field present on an already small map screen would be a nice toggle-able option? If not already possible, perhaps it could be put forward as a suggestion.

Many thanks

not possible. If a route is loaded the tooth will be there. Without TBT it will show the distance to the end of the route.

Mff73

@Boss-Hogg-450
there is no data tooth when not navigating a route, as far as i am seeing.

balbys70

Hi guys! Could you include a watch face with compass in the next update to vertical watch? I feel miss out from this. Is important to my use. I think you have an existent suunto race watch face with this complication allready. Thank you in advance

Stefano M64

After the last update the Blood Oxygen measurements on my Race seems to me to have started to give correct (or at least reasonable) readings, while before I always got values below 90%, however that “fix” isn’t listed in the Q3 release info. I also changed the strap (a nylon velcro band) but don’t believe that could have affected the readings in that way.

isazi

@Jordi-C I will see if I have some time to test this

isazi

@Jordi-C have you tried reboot her watch? They run the same software and both should work

Jordi C

@cosme-costa said in SW update 2.37.34 Q3:

@Jordi-C But which sport mode was using your wife? I mean, if she was in the GYM probably wasn’t using a GPS sports mode besides if she took the bus probably she lost the GPS signal, so the watch wasn’t able to detect she was moving.

It worked for me yesterday with a SV, in your case I would do a soft reset and see if it works again.

After leaving the gym she switched to “walk mode” and walked to the bus stop that is a few hundred meters away from the gym.
Of course, she always waits for GPS fix before starting any outdoor activity.

Jordi C

@isazi

yes, her watch was rebooted 2 or 3 times.

This problem started with latest firmware 2.37.34 Q3, on previous firmwares her watch was working without any issue.
She is going to repeat the “bus test” later this afternoon. I will post results later.

isazi

@Jordi-C sorry I was thinking you were talking about the message you get when you forget to restart a paused activity. I have no car so cannot test the abnormal speed detected, never seen that message.

So, what I understand now:

She uses the gym profile
She long press the top button to switch to walk profile
Walks to the bus stop
Forgets to end the activity, and rides the bus measuring a very fast walk

sartoric

@isazi said in SW update 2.37.34 Q3:

. I have no car so cannot test the abnormal speed

Run faster

Boss-Hogg-450

@Mff73 Thanks, but in this case, it was the routing aspect that i was interested in. I’m kinda surprised there is no option to disable it when not using TBT. Hopefully it’s something they’ll consider.

Jordi C

@isazi said in SW update 2.37.34 Q3:

@Jordi-C sorry I was thinking you were talking about the message you get when you forget to restart a paused activity. I have no car so cannot test the abnormal speed detected, never seen that message.

So, what I understand now:

She had both problems, no message when you forget to restart a paused activity and no message when abnormal speed

About the abnormal speed message:

She uses the gym profile
She stops gym profile and saves activity
She starts a new activity activating walk profile
She Walks to the bus stop
She forgets to end the activity, and rides the bus

But, unfortunately, when she was riding the bus, the “abnormal fast speed warning” never poped up.

Both warnings were working fine in her watch in the previous firmware.

EDIT:
my wife tested right now the “abnormal speed message” and it worked fine today!

EDIT2:
She tested again the message when you forget to restart a paused activity and unfortunately it didn’t worked.

far-blue

@Mff73

Ars Vitae

@Artus-Diver You can edit results by yourself in app, I am doing this because the watch doesn’t recognize exercises such as those for legs and butterfly style. By the way, congrats, I wish I had such a pace in swimming:)

Luis Andés Olmedo

Today, I detected two bugs in the Vertical while navigating a 30km route. The first is that the turn notifications sometimes appear in full-screen mode. The second (and more serious) issue is that the backlight often doesn’t turn on when I twist my wrist or when a notification (lap or turn) appears (after some tests I detected that it turns on if I keep the wrist twisted for 8 seconds or so). This was a problem because I was in a dark forest, and it was difficult to see the screen. At night, the watch would have been unusable.

The_77

@Luis-Andés-Olmedo said in SW update 2.37.34 Q3:

The first is that the turn notifications sometimes appear in full-screen mode.

This for me too, but I wanted to test again today to make sure, it shouldn’t occur on the nav screen anymore theoretically.

Luis Andés Olmedo

@The_77 it does (in the nav screen) but randomly.

The_77

@Luis-Andés-Olmedo I had that today again riding my bike, in the nav screen every time, both forwards and reverse routes.

Jordi C

More strange things from my wife’s Race S

Insane climbing metrics!

Second time this happens, first time was last month.

far-blue

@Jordi-C wow, that’s twice the distance from the surface to geostationary satellites. Kudos to your wife Sounds like she’s invented the new sport of “Vertical Running”