Software update 2.39.20 (2024 Q4)
-
@duffman19 you can add multiple ruler points on the watch and it will tell you the total distance.
Plus you can tap on the map and save the target as a POI.
Plus you can navigate to where you tap on the map.
Etc -
@Egika on that note of changes - what exact behaviour should occur with the tooth change vs what I observed? The only thing I can think of is that I deleted a couple of turns as superfluous after making the route initially, is there a logic behind it overriding the tooth in every scree
-
@Egika
Ah, yes! I don’t use POIs or the ruler often, but I can see how those are welcomed features for those who do. Suunto’s on-watch mapping experience is still my favorite (save for the tbt implementation - my one pet peeve!).Speaking of maps, any news on updates? Feels like it’s been a long while since anywhere outside of the Tour du Mont Blanc has been refreshed.
Edit: Looks like @pavel-samokha answered my question here - https://forum.suunto.com/post/159216
-
Can anyone show what does new zoom UI look like?
-
-
Hey first of all thank you all for the comments.
I hope it’s clear that we listen and we try to make the best out of what your feedback is. There is no good or bad feedback. All feedback is good. Just to be clear.
Let’s do some training tomorrow (idk I like Sundays to do some Xtra miles), and if it all goes well and internal testing shows that the build I am using (along with other testers) fixes the s9pp issue with ohr I’ll post it here so you can have it in advance of production release. Hopefully that’s the case.
Till then, rest , recover and thank you.
-
Software: 2.39.20
Device: Suunto Race Titanium
Heart Rate Sensor: Garmin HRM Pro (shown as paired)
FP Sensor: Stryd (shown as paired)
Power Management: Performance
Suunto Plus: ZoneSense
Potential issue: Infrequent heart rate samples - sporadic, a few points ever few minutesWent on an easy 30min run as I’m recovering from a cold. First run with the new firmware.
Here’s an image of the samples from intervals.icu (below). Garmin Connect reports the battery as good in my HRM pro. I took the dogs on a walk with the HRM pro and the data was continuous.
Run
Walk
Dogs
Suunto Race Titanium
Suunto Vertical Titanium
Suunto 9 Peak Pro Forest Green
Suunto 9 Peak Moss Gray -
@seanvk this looks bad. Is it in the app like this as well ?
-
@Dimitrios-Kanellopoulos It is odd because it appears as continuous in the app, but when looking at the watch while running, the heart rate most just “----” most of the time and only sporadically had a value when I happened to glance at it at the right time.
Not sure how to IM, but I can send you my FIT file.
Suunto Race Titanium
Suunto Vertical Titanium
Suunto 9 Peak Pro Forest Green
Suunto 9 Peak Moss Gray -
This post is deleted! -
@seanvk said in Software update 2.39.20 (2024 Q4):
@Dimitrios-Kanellopoulos It is odd because it appears as continuous in the app, but when looking at the watch while running, the heart rate most just “----” most of the time and only sporadically had a value when I happened to glance at it at the right time.
Not sure how to IM, but I can send you my FIT file.
It looks like the belt doesn’t work well.
-
@seanvk I have a Garmin HRM Pro too, and this problem you observed happens to me from time to time as well, though very rarely. It’s due to bad connection with the chest strap, which can include poor signal (for instance if the strap is not wet). Make sure it’s not connected to your phone (if you have it with you while running), I disconnected it from Garmin Connect, too, and it works.
S9PP
S5 -
@Dimitrios-Kanellopoulos Sorry to insist about the broken “Control panel” introduced by latest firmware, but may we also expect a fix for this issue in the next firmware update? Thanks a lot.
Suunto Vertical
Suunto Traverse -
-
Hi,
Apologies if this is somewhere further up the thread - I haven’t had time to read all the posts to check - but has anyone else found that the GPS (GNSS) run time on the S9PP has collapsed since the update?
I used my watch for an 8 hour run today and it used 51% of the battery (93% down to 42%) - which means it would struggle to last 15hrs. This is using the exact same settings - with an external hr monitor - that has consistently given me runtimes of 45-50hrs in the nearly 2 years I’ve had the watch (or, more accurately, two watches, because the first was replaced in January after the hr sensor cover failed a second time, so my current watch is about 11 months old).
I’ve checked that the backlight settings haven’t changed following the update and they haven’t - still set as low brightness, backlight (standby) and raise to wake both off. -
Just piling on that the HRM is no longer working on my 9PP. Have to restart every couple hours, works for a bit, then nothing. Hopefully the fix is pushed very soon. Kind of defeats the purpose of the watch.
-
@pavel-samokha said in Software update 2.39.20 (2024 Q4):
ruler point markers in map
is there any guide of how this works or what actually are the options ?
-
Hello, hi and bye bye.
After this update 9 peak pro isnt working as it shoud be!
After few hours heart rate isnt working also sleep measure isnt working. Then soft reset and this works few hours and then not…
This is really annoying!!!
Hard reset and soft --> nothing
And I cant connect win 11 and this 9 peak pro, why not?
Can I downgrade or what should I do.
Or do you wanna buy this watch
-
Suunto Vertical Ti
Suunto S9 gen1
Suunto Ambit3 peak -
@pavel-samokha since the update Heart rate monitor, sleep track and co2 level stopped working on 9peak pro completely!
Where and how to downgrade the firmware back to the one of Oct. 2024. Because with that one, all worked fine.
Anyone information about how to downgrade a firmware? Using android app.
