Suunto Vertical: Bug Collection
-
@isazi : SW update 2.37.34 Q3 Installed. I saw several watch faces marked as installed, but only default one was in watch (Vertical). I uninstalled and installed again, but still the default one was in watches (and 0/9 shown in SuuntoApp Watch faces section). I had to uninstall them all again, KILL the app (iOS) and install it again. It was ok then, I have installed faces in watches and counter shows correct installed number).
-
@thailon the first sync takes time, after update the watch needs to check and/or reload all your S+ apps, guides, watch faces. It should be fine from now on.
-
update 2.37.34
- map is in grey mode
- watch face also without colors
restart did not help
please fix this
-
@matus69 said in Suunto Vertical: Bug Collection:
update 2.37.34
- map is in grey mode
check the map option if not setup to high contrast
-
@Mff73 no, it is on Outdoor.
However I changed to all possible modes, but it is remains grey all the time -
@matus69
Strange. Either delete the map and redownload it or wait for more expert advise. -
I apologize, after all it is my mistake. Somehow the map got to full zoom and as I was in residential area, there were only buildings, no forest, no main road…that is why all appeared grey
After zooming out I see it in color.So sorry for confusion…
-
@matus69 Perfect
-
@jjorgemoura said in Suunto Vertical: Bug Collection:
When I start a new activity using any of those custom modes, the battery mode is always set to “custom”, even if I 100% of the times change it back to performance.
Same here
-
@Luis-Andés-Olmedo as far as I remember, if there is a custom battery mode is always preferred. Delete the custom mode, and it will default to performance.
-
@isazi thank you! I’ll do it… but… how can I delete the custom mode?
BTW, has anyone reported any delay in backlight activation with the new update? I am having random delays (no matter if in an activity or not… sometimes the backlight takes up to 8’’ to turn on upon wrist twist, notification or button press) since I updated.
-
@Luis-Andés-Olmedo said in Suunto Vertical: Bug Collection:
@isazi thank you! I’ll do it… but… how can I delete the custom mode?
you can’t in the fact, but you can set up the “custom mode” with the same settings as the performance one
(as far as i remember this tricky trick) -
Hello,
I realised something that confused me…
10 minutes in treadmill exercise mode, 903 steps and 33 kcal added to the Total from the exercise and again 10 minutes with just counting steps, 907 steps, it count these steps as 49 kcal+11 kcal from BMR, 60 kcal added to Total, so, same exercise, same time with very big difference in calories calculation. I’m wondering, where is the truth? -
I have noticed a strange behavior on 2.37.34 when I left for quite a long time (5-7min) the screen waiting to START in cycling activity.
Normally we do that for GPS to sync but this time I left it for some more time as I was preparing for the ride.The screen kept trying to go down the menu by itself and even trying to go up to start the session was impossible.
I have not tried to reproduce since this bug so I do not know if this is spontaneous.
-
@markman8
no water/liquid on the screen ? it has strange effects some times -
@Mff73 No. I checked it twice.
-
@isazi Hello, after updating to 2.37.34 last week, the watch started to reset to safe mode and wrote firmware error 1504, I don’t know if it’s critical?
-
@dzembronja may indicate some hardware issue, contact support
-
@isazi
Результати перекладу
No, after that I pressed ok, it started working, there is another problem after the update when I turn it off, there is no vibration when I turn it on, as it was before, for example, do not disturb, turn on the vibration, there is no vibration when it is turned off, there is also a problem with charge consumption after synchronization, this will be fixed in the next update, right? -
@isazi You say this is all not critical with that firmware error, right? And the high battery consumption after synchronization will be fixed, right?
