Software update 2.39.20 (2024 Q4)
-
Same here. 1h47min of sleep according to S9PP, then no more HR after that.
-
Hi @SuperFlo75 @taziden @Александр-Даниленко @Francesco-Pagano @Janne-Leppamaki @The_77
Please send logs via the app and send me a private message with your email address used in the app to check the issue with OHR stop working.
Could you help me out ?
-
@Dimitrios-Kanellopoulos
Same issue observed here, 9PP shows no OHR at all. Sensor is off. Won’t work or get active in the context of an activity either (OHR on, sensor/belt HR off). HR widget shows “Heart rate - not measured”.Soft reset restored OHR back.
Keeping an eye on how this develops!
-
@BrunoH I tried everything and my Control Panel was still broken. I gave up on it and went to work. Now it’s repaired by itself. Took literally no extra actions. Maybe just give it some time and it will be cured.
-
S9PP here, and no sleep tracking for 2 days now. OHR needs a soft reset to start working again.
-
Seems this is an issue for all 9PP users. Also being reported on Reddit.
Mine is the same - heart rate readings too high when working, but frequently OHR sensor not working at all, and sleep tracking also broken.
-
The same for me S9PP stopped OHR at midday yesterday until I did a reset and only recorded 1.12h sleep last night.
On a more positive note my suunto smart belt seem to be connecting to the watch again following connection issues with the previous FW. -
No problems with my S9PP. I had the issue with an earlier firmware, but since the last two updates it seems to be solved.
-
so far the update is exceptional… leading me to also sell the AWU . it’s simply great an update
-
On the positive side, this issue with OHR stopping is saving me quite a lot of battery charge
-
@cheetah694 mine was the same. Just started working.
-
@thanasis how about battery drain problems and offset, back to normal?
AWU what it is? -
Logs sent. Hopefully those help
-
new update, but still without Ukrainian language… very sad…
-
@pilleus said in Software update 2.39.20 (2024 Q4):
No problems with my S9PP. I had the issue with an earlier firmware, but since the last two updates it seems to be solved.
Same here! (At the moment…
) -
Hi guys, on 9pp, it seems there is a problem with the counting of watch faces installed on the watch, the default one is not considered and therefore when you get to 3/4, it does not install others. On the counting of sleep hours, it also seems to me that they are counted badly, battery life instead perhaps improved slightly (used 30% in two days with an hour of indoor activity without GPS) but I prefer to wait a few charge cycles to see if it has improved/resolved (I did both hard reset and restart, after the firmware update)
-
@Dimitrios-Kanellopoulos said in Software update 2.39.20 (2024 Q4):
Hi @SuperFlo75 @taziden @Александр-Даниленко @Francesco-Pagano @Janne-Leppamaki @The_77
Please send logs via the app and send me a private message with your email address used in the app to check the issue with OHR stop working.
Could you help me out ?
I sent it just now
As additional information, here is the video showing that OHR doesn’t respond at all (even activity start or oxygen blood measurement):
https://youtu.be/lnAEC9PiR98?si=Ndj0l9qhMBsaDRyD
P.S. OHR stopped working 3rd time for the last 2 days.
-
@BrunoH said in Software update 2.39.20 (2024 Q4):
@kriskus no amount of soft resets or language changes can fix this on my Vertical.
Same issue on my Vertical
Still persists after several reboot/soft reset.
Any advice is welcome. -
@MirkoP said in Software update 2.39.20 (2024 Q4):
Otherwise I will forced to make a firmware downgrade, waiting for a fixing of this annoying bug.
How to make a firmware downgrade?
-
@sebchastang Update: “control panel” works as expected now after powering off the watch, let it rest on the table for 15 minutes and restart it
